Bose 161 Technical Information download pdf (Page 6)

Testing speaker connections

1. Center the balance control on your receiver or amplifier. Set it

for MONO, if you have that option, and turn it on.

2. Place the 161’” speakers less than 6 inches (15 cm) apart, fac-

ing each other.

3. Play some deep bass passages of music.

The sound should seem to come from a point between the two

speakers. The bass should be full and natural. If not, your connec-

tions may be reversed, causing the speakers to play out of phase.

To correct the problem, make sure the speaker wires are con-

nected + to + and -to -. Then repeat steps 1 - 3.

Mounting your speakers on a wall

See the back pages of this guide for a mounting template and

mounting hardware information.

CAUTION: Do not mount the brackets on surfaces that are not

sturdy enough, or that have hazards concealed behind them,

such as electrical wire or plumbing. If you are unsure about install-

ing the bracket, contact a qualified professional installer.

CAUTION: Do not hang items from the brackets or speakers. The

brackets were designed to support the weight of the speakers

only

P Note: For vertical mounting, mount part A with the hole for screw

C at the bottom. Be sure to tighten all screws.

J Note: For Stereo Everywhere@ speaker performance, horizontal

mounting is required.

1. Hold the mounting template in position and mark holes for the

mounting hardware. If you plan to feed wires through the wall,

mark the speaker wire pilot hole also.

2. Drill holes for the chosen mounting hardware.

3. Mount bracket part A to the wall and mount bracket part E3 to

the rear of the speaker (Figure 3).

4. Secure the speaker with bracket part 6 to bracket pat-t A

using screw C. To adjust the angle, loosen screw C slightly,

move the speaker up or down, and retighten screw C.

Figure 3

Speaker-bracket

installation

Testing

speaker

connections

Center the balance control on your receiver or amplifier. Set it

for MONO, if you have that option, and turn it on.

Place the

161

speakers less than 6 inches

(15

cm) apart, fac-

ing each other.

Play some deep bass passages of music.

The sound should seem to come from a point between the two

speakers. The bass should be full and natural. If not, your connec-

tions may be reversed, causing the speakers to play out

phase.

correct the problem, make sure the speaker wires are con-

nected

+ to + and - to

Then repeat steps 1 -

Mounting

your

speakers on a

wall

See the back pages of this guide for a mounting template and

mounting hardware information.

A CAUTION:

not mount the brackets

surfaces that are not

sturdy enough, or that have hazards concealed behind them,

such as electrical wire or plumbing. Ifyou are unsure about install-

ing the bracket, contact a qualified professional installer.

A CAUTION:

not hang items from the brackets or speakers.

The

brackets were designed

support the weight

the speakers

only

) Note: For vertical mounting, mount

part

A with the hole for screw

the bottom. Be sure

tighten all screws.

)

Note:

For Stereo Everywhere® speaker performance, horizontal

mounting

required.

Hold the mounting template

position and mark holes for the

mounting hardware. If you plan to feed wires through the wall,

mark the speaker wire pilot hole also.

Drill holes for the chosen mounting hardware.

Mount bracket part A to the wall and mount bracket part B to

the rear

the speaker (Figure

3).

Secure the speaker with bracket part B to bracket part A

using screw

adjust the angle, loosen screw C slightly,

move the speaker up or down, and retighten screw

Figure 3

Speaker-bracket

installation

1 2 3 4 5 6 7 8 9 10 11 ... 18 19

Comments to this Manuals

No comments

Bose 161 Technical Information Page 6

Comments to this Manuals

Related products and manuals for Soundbar speakers Bose 161