Bose Auditioner Playback System III User's Guide download pdf (Page 9)

Using Auditioner

Playback System III

Svenska Nederlands Italiano Français Español Deutsch Dansk EnglishDanskDeutschItalianoNederlandsSvenska Français Español English

Auditioner

Playback System III User Guide

Connecting one Auditioner

Playback System III to another (daisy chaining)

Figure 7

You can daisy chain up to

12 Auditioner

Playback

System IIIs.

You can daisy chain up to 12 Auditioner playback system units. All Auditioner playback

systems will play the same audio as the “parent” system, and each Sound Pressure Level

meter will show the same level for all connected playback systems. The USB activity light will

only be illuminated on the "parent" system. The “parent” system receives the digital signal

from the computer. Each additional “child” system is daisy-chained to the “parent” by an

analog connection.

Note: During presentations, we recommend that you place the parent system so that the pre-

senter can see the USB activity light on the back of the Auditioner playback system. This will

allow the presenter to easily verify that sound data is being input into the daisy-chained sys-

tems.

Figure 8

Daisy chain connections

Follow these steps to daisy chain Auditioner playback system units:

1. Connect the Auditioner playback system’s USB cable from the USB port of your com-

puter (or USB hub) to the USB input on the Auditioner playback system. Connect the A

end (the larger end) to the laptop (or USB hub) and the B end (the smaller end) to the

Auditioner playback system. This will be the "parent" System.

2. Connect the parent playback system's RCA “OUT" to the second (child) playback sys-

tems RCA "IN"

3. Connect the second (child) playback system's RCA “CHAIN" to the third (child) playback

system's RCA "IN".

4. Connect the third playback system’s RCA “CHAIN” to the fourth system’s RCA “IN”.

5. Repeat step 4 until all Playback systems are connected.

6. Power on each system by flipping the power switch located on the back panel of each

Auditioner playback system.

Using Auditioner

Playback System III

English Deutsch FrançaisDansk Español Italiano SvenskaNederlandsDansk Italiano SvenskaDeutsch NederlandsEnglish FrançaisEspaño l

Auditioner

Playback System III User Guide

Using Auditioner Playback System III

Powering the unit on

The On/Off switch is located on the back of the Auditioner playback system. Press the

switch into the On position to turn the unit on. If the unit does not power on, make sure it is

plugged in.

Note: The Auditioner playback system has been designed to work only with the Bose

Modeler

Plus software. Although it is possible to connect Auditioner playback system as a

standard USB audio device, or as an analog audio device, any signal that Auditioner playback

system receives would not be equalized for the playback system. As a result, the audio signal

will be spectrally and spatially incorrect.

Adjusting the chin rest

Figure 5

Use both hands to adjust

the Auditioner

Playback

System III chin rest.

Follow these steps to adjust the chin rest:

1. Place one hand on the chin rest.

2. Press the chin rest adjuster with your other hand. Take care not to pinch your hand or

fingers as you adjust the position.

3. Gently push the chin rest up or down until it is in a comfortable position

Note: When you store the Auditioner playback system, make sure the chin rest is pushed

down as low as it can go so that it will fit into the carrying case.

1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments

Bose Auditioner Playback System III User's Guide Page 9

Comments to this Manuals

Related products and manuals for Supplementary music equipment Bose Auditioner Playback System III