Bose CE-1 CONTROL EXPANDER UNIT Operations Instructions Page 33
- Page / 84
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
33
GB
Getting Started
3 Measurement starts.
The measurement process will take a few
minutes to complete.
The table below shows the display when
measurement starts.
* The corresponding speaker indicator lights
up in the display during measurement.
4 Measurement ends.
“COMPLETE” appears on the display
and the settings are registered.
When you have finished
Disconnect the optimizer microphone from the
AUTO CAL MIC jack.
Notes
• Auto Calibration cannot detect the subwoofer.
Therefore, all subwoofer settings will be
maintained.
• If you have changed the position of the speakers, it
is recommended that you perform Auto Calibration
again in order to enjoy the surround sound.
Tips
• When Auto Calibration starts:
– Stand some distance from the speakers and the
listening position to avoid measurement failure.
This is because test signals are output from the
speakers during measurement.
– Avoid making noise to get a more accurate
measurement.
• The Auto Calibration function will be canceled
when you do the following during the
measurement process:
– Press ?/1 or MUTING.
– Press the input buttons or turn the INPUT
SELECTOR on the receiver.
– Change the volume level.
– Connect the headphones.
– Press AUTO CAL again.
When error codes appear
When an error is detected during Auto
Calibration, an error code will appear on the
display cyclically after each measurement
process as follows:
Error code t blank display t (error code t
blank display)
a)
t PUSH t blank display
t ENTER
a)
Appears when there are more than one error code.
To rectify the error
1 Record down the error code.
2 Press .
3 Press ?/1 to turn off the receiver.
4 Rectify the error.
For details, see “Error codes and remedies”
on page 34.
5 Turn on the receiver and perform Auto
Calibration again (page 32).
Measurement for Display
Environment noise
level
NOISE.CHK
Speaker connection MEASURE and SP
DET. appears
alternately*
Speaker level MEASURE and GAIN
appears alternately*
Speaker distance MEASURE and
DISTANCE appears
alternately*
Error and warning codes
continued
- Home Theatre 1
- About This Manual 2
- On Copyright 3
- Table of Contents 4
- Using the Remote 5
- Additional Information 5
- Front panel 6
- Name Function 7
- Rear panel 10
- 50mA MAX 11
- Remote commander 12
- 1: Installing the speakers 15
- 3 Hang the speakers on the 16
- Connecting the speakers 17
- To connect the speakers 18
- Connecting the subwoofers 19
- CENTER SURROUND BACK 20
- SURROUND 20
- SYSTEM CONTROL 20
- Audio/video 21
- Video signals 21
- Audio signals 21
- 4a: Connecting the audio 22
- Component to be connected 23
- A HDMI cable (not supplied) 24
- C Audio cord (not supplied)* 24
- To enjoy TV multi channel 25
- HDMI features 25
- Notes on HDMI connections 25
- Connecting a DVD player, Blu 26
- B Video cord (not supplied) 27
- D Audio cord (not supplied) 27
- DVD recorder, VCR 28
- Audio signalsVideo signals 28
- (On the front panel) 28
- Camcorder/ 28
- 5: Connecting the 29
- 6: Preparing the receiver 30
- 1 Press ?/1 to turn off the 30
- 7: Calibrating the 31
- 2 Set up the optimizer 32
- 1 Press AMP MENU 32
- 2 Press AUTO CAL 32
- 3 Measurement starts 33
- 4 Measurement ends 33
- Error codes and remedies 34
- When warning codes appear 34
- To change the settings 34
- Warning codes and solutions 34
- (TEST TONE) 35
- Selecting a component 36
- Naming inputs 37
- MASTER VOLUMEINPUT SELECTOR 38
- Watching a DVD/Blu-ray disc 39
- Amplifier Operations 40
- Overview of the menus 41
- Adjusting the level 43
- Adjusting the equalizer 44
- Settings for the surround 44
- Using the surround back 45
- Settings for the tuner 46
- Settings for the audio 46
- Settings for the HDMI 48
- Settings for the system 48
- Calibrating the 50
- Enjoying Dolby Digital 51
- Types of A.F.D. mode 52
- Selecting a pre 53
- Using only the front 55
- (NIGHT MODE) 56
- Listening to FM/AM radio 57
- 1 Press TUNER repeatedly to 57
- 2 Press TUNING + or TUNING – 57
- (Direct Tuning) 58
- Changing the AM tuning scale 58
- Tuning to preset stations 59
- Naming preset stations 60
- “BRAVIA” Sync Features 60
- Preparing for the 61
- “BRAVIA” Sync 61
- Watching a DVD 63
- Enjoying the TV sound 63
- Turning off the receiver 64
- Audio input modes 65
- (DIGITAL ASSIGN) 66
- Enjoying the DIGITAL 67
- MEDIA PORT 67
- 1 Press DMPORT 68
- Changing the display 69
- Using the Sleep Timer 69
- Recording onto a CD-R 70
- Recording onto a recording 70
- Changing button 71
- Glossary 72
- Precautions 74
- Troubleshooting 75
- (not supplied) 78
- Outdoor FM antenna (aerial) 78
- Receiver 78
- To ground 78
- Ground wire 78
- To clear See 79
- Specifications 80
- Printed in Malaysia 84
Related products and manuals for AV receivers Bose CE-1 CONTROL EXPANDER UNIT
(23 pages)© 2020, manymanuals.com. All rights reserved. | 1.433 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals