Bose 40 User Manual

Bose® FreeSpace® DS 40SE Loudspeaker* For use by professional installers only.* Kun til brug for erfarne installatører.* Montage ausschließlich durch

10Wiring the BracketCeramic terminal and thermal switchTo meet combination systems specifications required in some regions of Europe (see page 28)The

11Wiring the BracketWire gauge requirementsFrom bracket to ceramic blockUse thermal switch (fuse) and wires included with the Bose® accessories.From l

12Direct mount with in-wall wiring• Use M4 or #8 screws with appropriate anchors. • At least two (2) screws must be used to hold the wall mount bracke

13Mounting the BracketPreparing the wire for direct mount with on-wall wiringTrim back the outer jacket (A) and some of the wire insulation (B) to exp

14Mounting the BracketDirect mount with on-wall wiring1. Remove bracket door(s).2. Center wires over strain relief clamp hole and insert strain relief

15Mounting the BracketMontage direct avec câbles sur le mur1. Déposer le couvercle du support.2. Centrer les câbles au-dessus de l’orifice de la langu

16Mounting the BracketWith Bose® On-Wall Junction Box1. Attach junction box to wall:• Use M4 or #8 screws with appropriate anchors. • At least two (2)

17Mounting the BracketAvec boîtier Bose® de branchement sur le mur1. Fixer la boîte de jonction au mur :• Utiliser des vis M4 ou n° 8 avec les chevill

18Mounting the BracketWith Bose® In-Wall Junction Box1. Use cutting template and instructions included with the Bose In-Wall Junction Box.2. Cut hole

19Mounting the BracketAvec boîtier Bose® de branchement dans le mur1. Utiliser le gabarit et le feuillet d’instructions fournis avec la boîte de jonct

Bose® FreeSpace® DS 40SE Loudspeaker*For use by trained installers only.*Kun til brug for erfarne installatører.*Montage ausschließlich durch ausgebil

20Mounting the BracketWith standard steel 4" x 4" junction boxThe FreeSpace® DS 40SE loudspeaker can be mounted directly on standard U.S. s

Bose® DS Trim Plate (accessory)21Mounting the BracketWith standard steel 4" x 4" junction boxThe FreeSpace® DS 40SE loudspeaker can be moun

2.26"57.5 mm4"–8"(101.6 mm – 203.2 mm)1.5"–4"(38.1 mm – 101.6 mm)22Mounting the BracketWith Bose® Pole Mount Kit1. Poles 4&qu

23Mounting the BracketAvec le kit de montage sur poteau Bose®1. Poteaux de 4" à 8" (101,6 mm à 203,2 mm): Visser la pince à travers les ouve

24Positioning and securing the loudspeaker1. Align the holes of the loudspeaker arm and bracket.2. Insert, but DO NOT TIGHTEN, the fastener: P2 Phil

25Mounting the Loudspeaker to the Wall BracketPositionnement et sécurisation du haut-parleur1. Aligner les trous du montant de l’enceinte et du suppor

26Plug the wire into the bracket1. Remove paint shield (if not already removed).2. Snap on loudspeaker wire plug to bracket connector.3. Insert and ti

27Other ConsiderationsUsing the safety cable insert• Some regional construction codes require the use of a secondary method of securing loudspeakers t

28The DS 40SE has passed extensive testing and complies with the following specifications and uses:LISTED to ANSI/UL 1480-2005• Fire Protective Signal

DS40SE.book Page 29 Friday, March 26, 2010 2:53 PM

3Installation• Choose a mounting position, method, and hardware consistent with local building codes and regulations. • Due to various construction me

DS40SE.book Page 30 Friday, March 26, 2010 2:53 PM

DS40SE.book Page 31 Friday, March 26, 2010 2:53 PM

©2010 Bose Corporation, The MountainFramingham, MA 01701-9168 USAAM325611 Rev.00pro.Bose.comDS40SE.book Page 24 Friday, March 26, 2010 2:53 PM

4Mounting and junction box options1. Direct mount (in-wall or on-wall wiring)2. Bose® On-Wall Junction Box (accessory)3. Bose® In-Wall Junction Box (a

5Installation OptionsLoudspeaker orientation and angle1. Horizontal and pitch — Adjustment range +30° – -45°2. Horizontal and yaw — Adjustment range +

70V2.5W* 5W 10W 20W 40W8Ω5W* 10W 20W 40W NC**100V* Factory default ** NC: No Connection (do not use)* Fabriksstandard ** NC: Ingen forbindelse (undg

7Preparing the Loudspeaker Before Mounting VerticallyRotating logoFor vertical mounting:1. Firmly grasp logo and pull away from grille.2. Rotate logo

8Rotating loudspeaker armFor horizontal mounting with yaw adjustment or vertical mounting with pitch adjustment:1. Remove screws from loudspeaker arm.

9Wiring the Bracket Wire gauge requirementsFrom loudspeaker line wiring to bracketUse 18 AWG (0.8 mm2) to 14 AWG (2.0 mm2) size wire only.Krav til led